Testing Equipment

Product Details:

contaminating the surface prior to the coating application.This contamination can be tested quickly and simply using the Bresle Test Kit. This kit has advantage over portable units. Test can be quickly performed at site, shop floor and plants. The Bresle Patch is attached to the surface; the distilled water is injected with a syringe then extracted, repeat ten cycles of injecting and extracting then measure with the Conductivity meter.Compact conductivity meter will measure the quantity of salts in ??g/cm2 (ppm) and mg/m2. Bresle test complies with ISO 8502-6, which relates to the extraction of soluble contaminants and ISO 8502-9, which relates to the conduct metric determination of soluble salts. Calibration Certificates traceable are available for the Conductivity Meter in the kit. The Bresle Test Kit is supplied with 50 Bresle Patches, 1 Conductivity Meter, Calibration Solutions, 5x5ml Syringes, 25ml Beaker and 250ml Distilled Water. Additional Bresle Patches can be purchased to carry out further tests using this kit. Part Numbers: BTK-001 Bresle Test Kit BTK-002 Bresle Patches(Pack of 50 Nos.) BTK-003 Bottle 250ml - Distilled Water.

Product Details:

Surface Roughness Comparator SA 2.5Dimensions: 10 x 10 x 0.5 cm

A precision Nickel comparator plate which conforms to International Standard ISO 8503 for grit and shotblast surface roughness comparison measurement. Popular comparators for grit blasting comparison or shot blasting comparison When steel has been blast cleaned, the surface consists of random irregularities with peaks and valleys that are not easily characterized. Experts have recommended that the profile should be identified as dimpled (shot blast) or angular (grit blast) and that they should be graded as Fine, Medium or Coarse with each grade being defined by limits specified in ISO 8503, these characteristics are considered to give sufficient distinguishing features for most painting requirements. Easy to use, place the surface roughness comparator against an area of the test surface, compare in turn the four sectors of the four sectors of the comparator against the test surface using the X7 magnifier, placed so that the test surface is viewed. There are two comparators shot blasting ,This is specially designed to check the roughness of steel surfaces which have been blast cleaned to cleanliness grades SA 2.5 comparators conform to ISO 8503

Additional Information:

• Production Capacity: 10
• Delivery Time: 2-3 days
• Packaging Details: Box

Product Details:

Surface profile guage

Product Details:

Holiday Testing Machine used for testing of wrapping coating on undergraound pipe line.

Springs Electrolde Size availble : Suitable for Pipe Diameter 2", 3", 4", 6", 8", 10", 12", 14", 16", 18", 20", 22", 24", 26", 28" and 30 inch.

Additional Information:

• Packaging Details: Box

Product Details:

Holiday Tester used for Holes / cuts detect / test on anti-corrosive coating.
Wrappings Coating is carried out on underground pipelines to protect from correction. 
Springs Electrolde Size availble : Suitable for Pipe Diameter 2", 3", 4", 6", 8", 10", 12", 14", 16", 18", 20", 22", 24", 26", 28" and 30 inch.

Additional Information:

• Delivery Time: 3-4 days
• Packaging Details: Box Packing

Product Details:

Wet film thickness guage use in measuring Paint DFT micron thickness during painting run. This wet film guage can measure from 25 micron to 2000 micron.

Product Details:

Product Details:

Press O Film Gauge Known as Dial thickness Gauge, we having both types of model : Digital Dial thickness gauge & Analog Dial thickness Gauge.

Additional Information:

• Production Capacity: 10
• Delivery Time: ready stock
• Packaging Details: box

Product Details:

Pin Hole Detector used for detect pin holes in coatings. Pin Hole Detector comes with sponge brush.

Additional Information:

• Delivery Time: 3-4 days
• Packaging Details: Box

Product Details:

Surface profile gauge or testex tapes can test surface roughness. Most commonly used testex tapes / press o films are popular as it can give permanent record of the surfaces as a proof of test. Place the Testex Tape (Press-O-Film) firmly on the blasted surface, apply moderate pressure with the burnishing tool, the replica has now been taken and can be measured using the snap gauge. Testing & Inspection can be done in three easy steps. Detailed procedure is furnished with testex kit or tapes. Testex Tape is supplied in a roll containing 50 tests and is available in four different grades to cater for different applications. The snap gauge is supplied in a carrying case with a burnishing tool. Paint applicators, inspectors and researchers for its simple operations and results prefers to use Testex tapes (Press-O-Film) Testex Tape (Press-o-film) complies with ASTM, NACE and SSPC methods measurement. ASTM- Reproducibility is given in ASTM Standard 4417-93 for both "X-coarse" and "coarse" grade replica tape. NACE- Standard RP0287-95 addresses the issue of accuracy of measurement, test results. SSPC- The Society for Protective Coatings, recommends a minimum of three measurements of profile per 100 square feet (10 square meters).  ISO- International Organization for Standards- Draft Standard ISO8503-5 describes preparation of steel

Product Details:

DFT meter